Author:
Publisher: Jeffrey Frank Jones
Published:
Total Pages: 197
ISBN-13:
DOWNLOAD EBOOKCONTENTS: TM 9-1005-229-35 54 pages – September 1969 w change 1 Maintenance Manual Contents CH 1 INTRODUCTION General Description and data CH 2 DIRECT SUPPORT, GENERAL SUPPORT AND DEPOT MAINTENANCE INSTRUCTIONS Repair parts, special tools, and equipment Troubleshooting Preembarkation inspections of material in units alerted for overseas movement General maintenance Removal and installation Depot maintenance procedures CH 3 REPAIR INSTRUCTIONS CH 4 FINAL INSPECTION Appendix A. REFERENCES Appendix B. DIRECT SUPPORT, GENERAL SUPPORT, AND DEPOT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LIST Introduction Repair Parts List Repair Parts For: Major groups, assemblies and components (figs B-1 and B-2) Bolt and guide rod group (fig B-3) Trigger housing group (figs B-4 and B-5) Trigger and sear group (fig B-6) Receiver assembly (figs. B-7 and B-8) Flash hider assembly (fig B-9) Oiler (fig B-10) Special Tools List (fig B-10) Index—Federal Stock Number and Reference Number Cross-Reference to Figure and Item Number TM 9-1005-229-12 60 pages – October 1969 w changes 1 & 2 Operation Manual Contents CH 1 INTRODUCTION General Description and data CH 2 OPERATING INSTRUCTIONS Controls Operation under usual conditions Operation under unusual conditions CH 3 OPERATOR AND ORGANIZATIONAL MAINTENANCE INSTRUCTIONS Service upon receipt of materiel Repair parts, special tools and equipment Lubrication instructions Preventive Maintenaice checks and services Troubleshooting Operators maintenance procedures Organizational maintenance procedures CH 4 AMMUNITION CH 5 DESTRUCTION TO PREVENT ENEMY USE Appendix A. REFERENCE Appendix B. MAINTENANCE ALLOCATION CHART Introduction Maintenance allocation chart for Caliber .45 Submachine Guns Appendix C. ORGANIZATIONAL MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LIST Introduction Basic issue items list (figs Cl and C3) Maintenance and operating supplies Prescribed load allowance Repair parts list Major groups, assemblies and component parts (fig Cl Bolt and guide rod group (fig C2 Oiler carbine (fig C3 Special tools, test and support equipment (fig.C-3 Index-Federal stock number and reference number cross-reference to figure and item number FM 23-41 DEPARTMENT OF THE ARMY FIELD MANUAL SUBMACHINEGUNS CALIBER .45 M3 AND M3A1 HEADQUARTERS, DEPARTMENT OF THE ARMY 28 JUNE 1974, 83 pages
Book Synopsis Manuals Combined: U.S. Army M3 M3A1 1969 1974 Submachine "Grease" Gun Parts, Service & Operator Technical Manuals by :
Download or read book Manuals Combined: U.S. Army M3 M3A1 1969 1974 Submachine "Grease" Gun Parts, Service & Operator Technical Manuals written by and published by Jeffrey Frank Jones. This book was released on with total page 197 pages. Available in PDF, EPUB and Kindle. Book excerpt: CONTENTS: TM 9-1005-229-35 54 pages – September 1969 w change 1 Maintenance Manual Contents CH 1 INTRODUCTION General Description and data CH 2 DIRECT SUPPORT, GENERAL SUPPORT AND DEPOT MAINTENANCE INSTRUCTIONS Repair parts, special tools, and equipment Troubleshooting Preembarkation inspections of material in units alerted for overseas movement General maintenance Removal and installation Depot maintenance procedures CH 3 REPAIR INSTRUCTIONS CH 4 FINAL INSPECTION Appendix A. REFERENCES Appendix B. DIRECT SUPPORT, GENERAL SUPPORT, AND DEPOT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LIST Introduction Repair Parts List Repair Parts For: Major groups, assemblies and components (figs B-1 and B-2) Bolt and guide rod group (fig B-3) Trigger housing group (figs B-4 and B-5) Trigger and sear group (fig B-6) Receiver assembly (figs. B-7 and B-8) Flash hider assembly (fig B-9) Oiler (fig B-10) Special Tools List (fig B-10) Index—Federal Stock Number and Reference Number Cross-Reference to Figure and Item Number TM 9-1005-229-12 60 pages – October 1969 w changes 1 & 2 Operation Manual Contents CH 1 INTRODUCTION General Description and data CH 2 OPERATING INSTRUCTIONS Controls Operation under usual conditions Operation under unusual conditions CH 3 OPERATOR AND ORGANIZATIONAL MAINTENANCE INSTRUCTIONS Service upon receipt of materiel Repair parts, special tools and equipment Lubrication instructions Preventive Maintenaice checks and services Troubleshooting Operators maintenance procedures Organizational maintenance procedures CH 4 AMMUNITION CH 5 DESTRUCTION TO PREVENT ENEMY USE Appendix A. REFERENCE Appendix B. MAINTENANCE ALLOCATION CHART Introduction Maintenance allocation chart for Caliber .45 Submachine Guns Appendix C. ORGANIZATIONAL MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LIST Introduction Basic issue items list (figs Cl and C3) Maintenance and operating supplies Prescribed load allowance Repair parts list Major groups, assemblies and component parts (fig Cl Bolt and guide rod group (fig C2 Oiler carbine (fig C3 Special tools, test and support equipment (fig.C-3 Index-Federal stock number and reference number cross-reference to figure and item number FM 23-41 DEPARTMENT OF THE ARMY FIELD MANUAL SUBMACHINEGUNS CALIBER .45 M3 AND M3A1 HEADQUARTERS, DEPARTMENT OF THE ARMY 28 JUNE 1974, 83 pages
