Download Partitioning Design Approach For The Reliable Design Of Highly Efficient Rf Power Amplifiers full books in PDF, epub, and Kindle. Read online Partitioning Design Approach For The Reliable Design Of Highly Efficient Rf Power Amplifiers ebook anywhere anytime directly on your device. Fast Download speed and no annoying ads. We cannot guarantee that every ebooks is available!
Book Synopsis Partitioning Design Approach for the Reliable Design of Highly Efficient RF Power Amplifiers by : Roshanak Lehna
Download or read book Partitioning Design Approach for the Reliable Design of Highly Efficient RF Power Amplifiers written by Roshanak Lehna and published by . This book was released on 2017 with total page 190 pages. Available in PDF, EPUB and Kindle. Book excerpt:
The modern wireless communication systems require modulated signals with wide modulation bandwidth. This, in turns, requires signals with very high dynamic range and peak-to-average power ratio (PAPR). This means that the amplifier in the base-station has to work at a power back-off as large as the dynamic range of the signal, so that the amplifier has a high linearity in this region. For the standard single-stage amplifiers, this large power back-off reduces the efficiency dramatically. In this work, a three-way Doherty power amplifier (DPA) aiming at high power efficiency within a dynamic range of 9.5 dB, is designed and fabricated using partitioning design approach. The partitioning design approach decomposes a complex design task into small-sized, well-controllable, and verifiable subcircuits. This advanced straight forward method has shown very promising results. Using this design approach, a three-way DPA has been designed to demonstrate the advantages of this reliable design technique as well. Based on the design of a single-stage power amplifier and proposing a novel output power combiner, a 6 W three-way DPA has been designed which allows the mandatory load modulation principle in three-way DPA structures to be realized with simpler elements, whereas the design of a standard Doherty combiner would have been very challenging and not practical due to the extremely small value of its characteristic line impedance. The proposed combiner is calculated for a three-way DPA with 2-mm AlGaN/GaN-HEMTs. The simulation result shows a very good load modulation for the amplifier, which confirms the theoretical expectation for a three-way DPA. The efficiency of the designed 6 W three-way DPA at large back-off shows very promising values compared to recently reported amplifiers. The measured IMD3 products confirm the good linearity of the amplifier as well. Accordingly, the proposed power combiner and the design strategy are recommended to be used as the preferred option for designing three-way DPA structures with very high output power.
Book Synopsis Partitioning Design Approach for the Reliable Design of Highly Efficient RF Power Amplifiers by : Roshanak Lehna
Download or read book Partitioning Design Approach for the Reliable Design of Highly Efficient RF Power Amplifiers written by Roshanak Lehna and published by kassel university press GmbH. This book was released on 2017-11-13 with total page 190 pages. Available in PDF, EPUB and Kindle. Book excerpt: The modern wireless communication systems require modulated signals with wide modulation bandwidth. This, in turns, requires signals with very high dynamic range and peak-to-average power ratio (PAPR). This means that the amplifier in the base-station has to work at a power back-off as large as the dynamic range of the signal, so that the amplifier has a high linearity in this region. For the standard single-stage amplifiers, this large power back-off reduces the efficiency dramatically. In this work, a three-way Doherty power amplifier (DPA) aiming at high power efficiency within a dynamic range of 9.5 dB, is designed and fabricated using partitioning design approach. The partitioning design approach decomposes a complex design task into small-sized, well-controllable, and verifiable subcircuits. This advanced straight forward method has shown very promising results. Using this design approach, a three-way DPA has been designed to demonstrate the advantages of this reliable design technique as well. Based on the design of a single-stage power amplifier and proposing a novel output power combiner, a 6 W three-way DPA has been designed which allows the mandatory load modulation principle in three-way DPA structures to be realized with simpler elements, whereas the design of a standard Doherty combiner would have been very challenging and not practical due to the extremely small value of its characteristic line impedance. The proposed combiner is calculated for a three-way DPA with 2-mm AlGaN/GaN-HEMTs. The simulation result shows a very good load modulation for the amplifier, which confirms the theoretical expectation for a three-way DPA. The efficiency of the designed 6 W three-way DPA at large back-off shows very promising values compared to recently reported amplifiers. The measured IMD3 products confirm the good linearity of the amplifier as well. Accordingly, the proposed power combiner and the design strategy are recommended to be used as the preferred option for designing three-way DPA structures with very high output power.
Achieve higher levels of performance, integration, compactness, and cost-effectiveness in the design and modeling of radio-frequency (RF) power amplifiers RF power amplifiers are important components of any wireless transmitter, but are often the limiting factors in achieving better performance and lower cost in a wireless communication system—presenting the RF IC design community with many challenges. The next-generation technological advances presented in this book are the result of cutting-edge research in the area of large-signal device modeling and RF power amplifier design at the Georgia Institute of Technology, and have the potential to significantly address issues of performance and cost-effectiveness in this area. Richly complemented with hundreds of figures and equations, Modeling and Design Techniques for RF Power Amplifiers introduces and explores the most important topics related to RF power amplifier design under one concise cover. With a focus on efficiency enhancement techniques and the latest advances in the field, coverage includes: Device modeling for CAD Empirical modeling of bipolar devices Scalable modeling of RF MOSFETs Power amplifier IC design Power amplifier design in silicon Efficiency enhancement of RF power amplifiers The description of state-of-the-art techniques makes this book a valuable and handy reference for practicing engineers and researchers, while the breadth of coverage makes it an ideal text for graduate- and advanced undergraduate-level courses in the area of RF power amplifier design and modeling.
Book Synopsis Modeling and Design Techniques for RF Power Amplifiers by : Arvind Raghavan
Download or read book Modeling and Design Techniques for RF Power Amplifiers written by Arvind Raghavan and published by John Wiley & Sons. This book was released on 2008-02-04 with total page 224 pages. Available in PDF, EPUB and Kindle. Book excerpt: Achieve higher levels of performance, integration, compactness, and cost-effectiveness in the design and modeling of radio-frequency (RF) power amplifiers RF power amplifiers are important components of any wireless transmitter, but are often the limiting factors in achieving better performance and lower cost in a wireless communication system—presenting the RF IC design community with many challenges. The next-generation technological advances presented in this book are the result of cutting-edge research in the area of large-signal device modeling and RF power amplifier design at the Georgia Institute of Technology, and have the potential to significantly address issues of performance and cost-effectiveness in this area. Richly complemented with hundreds of figures and equations, Modeling and Design Techniques for RF Power Amplifiers introduces and explores the most important topics related to RF power amplifier design under one concise cover. With a focus on efficiency enhancement techniques and the latest advances in the field, coverage includes: Device modeling for CAD Empirical modeling of bipolar devices Scalable modeling of RF MOSFETs Power amplifier IC design Power amplifier design in silicon Efficiency enhancement of RF power amplifiers The description of state-of-the-art techniques makes this book a valuable and handy reference for practicing engineers and researchers, while the breadth of coverage makes it an ideal text for graduate- and advanced undergraduate-level courses in the area of RF power amplifier design and modeling.
Advanced Design Techniques for RF Power Amplifiers provides a deep analysis of theoretical aspects, modelling, and design strategies of RF high-efficiency power amplifiers. The book can be used as a guide by scientists and engineers dealing with the subject and as a text book for graduate and postgraduate students. Although primarily intended for skilled readers, it provides an excellent quick start for beginners.
Book Synopsis Advanced Design Techniques for RF Power Amplifiers by : Anna N. Rudiakova
Download or read book Advanced Design Techniques for RF Power Amplifiers written by Anna N. Rudiakova and published by Springer Science & Business Media. This book was released on 2006-09-09 with total page 140 pages. Available in PDF, EPUB and Kindle. Book excerpt: Advanced Design Techniques for RF Power Amplifiers provides a deep analysis of theoretical aspects, modelling, and design strategies of RF high-efficiency power amplifiers. The book can be used as a guide by scientists and engineers dealing with the subject and as a text book for graduate and postgraduate students. Although primarily intended for skilled readers, it provides an excellent quick start for beginners.
This is the first book devoted exclusively to the outphasing power amplifier, covering the most recent research results on important aspects in practical design and applications. A compilation of all the proposed outphasing approaches, this is an important resource for engineers designing base station and mobile handset amplifiers, engineering managers and program managers supervising power amplifier designs, and R&D personnel in industry. The work enables you to: design microwave power amplifiers with higher efficiency and improved linearity at a lower cost; understand linearity and performance tradeoffs in microwave power amplifiers; and understand the effect of new modulation techniques on microwave power amplifiers.
Book Synopsis Design of Linear RF Outphasing Power Amplifiers by : Xuejun Zhang
Download or read book Design of Linear RF Outphasing Power Amplifiers written by Xuejun Zhang and published by Artech House. This book was released on 2003 with total page 222 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is the first book devoted exclusively to the outphasing power amplifier, covering the most recent research results on important aspects in practical design and applications. A compilation of all the proposed outphasing approaches, this is an important resource for engineers designing base station and mobile handset amplifiers, engineering managers and program managers supervising power amplifier designs, and R&D personnel in industry. The work enables you to: design microwave power amplifiers with higher efficiency and improved linearity at a lower cost; understand linearity and performance tradeoffs in microwave power amplifiers; and understand the effect of new modulation techniques on microwave power amplifiers.
A computationally efficient procedure for the design of RF power amplifiers is presented. The proposed approach allows for the identification of "near-optimal" source and load terminations of the amplifier stage providing maximum output power under assigned linearity, minimum gain and other possible constraints. The design procedure is completely based on closed form numerical computations, without requiring non linear optimisations as normally happens in standard design approaches. A single-stage 2.4 GHz amplifier prototype has been designed and manufactured in Silicon BJT MMIC technology, according to the criteria provided by the new methodology. Experimental results are in good agreement with simulations and confirm the validity of the proposed approach.
Book Synopsis A Computationally Efficient Approach for the Design of RF Power Amplifiers by :
Download or read book A Computationally Efficient Approach for the Design of RF Power Amplifiers written by and published by . This book was released on 2002 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: A computationally efficient procedure for the design of RF power amplifiers is presented. The proposed approach allows for the identification of "near-optimal" source and load terminations of the amplifier stage providing maximum output power under assigned linearity, minimum gain and other possible constraints. The design procedure is completely based on closed form numerical computations, without requiring non linear optimisations as normally happens in standard design approaches. A single-stage 2.4 GHz amplifier prototype has been designed and manufactured in Silicon BJT MMIC technology, according to the criteria provided by the new methodology. Experimental results are in good agreement with simulations and confirm the validity of the proposed approach.
This book presents a synthesis of the research carried out in the Laboratory of Signal Processing and Communications (LaPSyC), CONICET, Universidad Nacional del Sur, Argentina, since 2003. It presents models and techniques widely used by the signal processing community, focusing on low-complexity methodologies that are scalable to different applications. It also highlights measures of the performance and impact of each compensation technique. The book is divided into three parts: 1) basic models 2) compensation techniques and 3) applications in advanced technologies. The first part addresses basic architectures of transceivers, their component blocks and modulation techniques. It also describes the performance to be taken into account, regardless of the distortions that need to be compensated. In the second part, several schemes of compensation and/or reduction of imperfections are explored, including linearization of power amplifiers, compensation of the characteristics of analog-to- digital converters and CFO compensation for OFDM modulation. The third and last part demonstrates the use of some of these techniques in modern wireless-communication systems, such as full-duplex transmission, massive MIMO schemes and Internet of Things applications.
Book Synopsis Signal Processing Techniques for Power Efficient Wireless Communication Systems by : Fernando Gregorio
Download or read book Signal Processing Techniques for Power Efficient Wireless Communication Systems written by Fernando Gregorio and published by Springer Nature. This book was released on 2019-11-23 with total page 269 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents a synthesis of the research carried out in the Laboratory of Signal Processing and Communications (LaPSyC), CONICET, Universidad Nacional del Sur, Argentina, since 2003. It presents models and techniques widely used by the signal processing community, focusing on low-complexity methodologies that are scalable to different applications. It also highlights measures of the performance and impact of each compensation technique. The book is divided into three parts: 1) basic models 2) compensation techniques and 3) applications in advanced technologies. The first part addresses basic architectures of transceivers, their component blocks and modulation techniques. It also describes the performance to be taken into account, regardless of the distortions that need to be compensated. In the second part, several schemes of compensation and/or reduction of imperfections are explored, including linearization of power amplifiers, compensation of the characteristics of analog-to- digital converters and CFO compensation for OFDM modulation. The third and last part demonstrates the use of some of these techniques in modern wireless-communication systems, such as full-duplex transmission, massive MIMO schemes and Internet of Things applications.
Using the load-pull method for RF and microwave power amplifier design This new book on RF power amplifier design, by industry expert Dr. John F. Sevic, provides comprehensive treatment of RF PA design using the load-pull method, the most widely used and successful method of design. Intended for the newcomer to load-pull, or the seasoned expert, the book presents a systematic method of generation of load-pull contour data, and matching network design, to rapidly produce a RF PA with first-pass success. The method is suitable from HF to millimeter-wave bands, discrete or integrated, and for high-power applications. Those engaged in design or fundamental research will find this book useful, as will the student new to RF and interested in PA design. The author presents a complete pedagogical methodology for RF PA design, starting with treatment of automated contour generation to identify optimum transistor performance with constant source power load-pull. Advanced methods of contour generation for simultaneous optimization of many variables, such as power, efficiency, and linearity are next presented. This is followed by treatment of optimum impedance identification using contour data to address specific objectives, such as optimum efficiency for a given linearity over a specific bandwidth. The final chapter presents a load-pull specific treatment of matching network design using load-pull contour data, applicable to both single-stage and multi-stage PA's. Both lumped and distributed matching network synthesis methods are described, with several worked matching network examples. Readers will see a description of a powerful and accessible method that spans multiple RF PA disciplines, including 5G base-station and mobile applications, as well as sat-com and military applications; load-pull with CAD systems is also included. They will review information presented through a practical, hands-on perspective. The book: Helps engineers develop systematic, accurate, and repeatable approach to RF PA design Provides in-depth coverage of using the load-pull method for first-pass design success Offers 150 illustrations and six case studies for greater comprehension of topics
Book Synopsis The Load-pull Method of RF and Microwave Power Amplifier Design by : John F. Sevic
Download or read book The Load-pull Method of RF and Microwave Power Amplifier Design written by John F. Sevic and published by John Wiley & Sons. This book was released on 2020-06-23 with total page 192 pages. Available in PDF, EPUB and Kindle. Book excerpt: Using the load-pull method for RF and microwave power amplifier design This new book on RF power amplifier design, by industry expert Dr. John F. Sevic, provides comprehensive treatment of RF PA design using the load-pull method, the most widely used and successful method of design. Intended for the newcomer to load-pull, or the seasoned expert, the book presents a systematic method of generation of load-pull contour data, and matching network design, to rapidly produce a RF PA with first-pass success. The method is suitable from HF to millimeter-wave bands, discrete or integrated, and for high-power applications. Those engaged in design or fundamental research will find this book useful, as will the student new to RF and interested in PA design. The author presents a complete pedagogical methodology for RF PA design, starting with treatment of automated contour generation to identify optimum transistor performance with constant source power load-pull. Advanced methods of contour generation for simultaneous optimization of many variables, such as power, efficiency, and linearity are next presented. This is followed by treatment of optimum impedance identification using contour data to address specific objectives, such as optimum efficiency for a given linearity over a specific bandwidth. The final chapter presents a load-pull specific treatment of matching network design using load-pull contour data, applicable to both single-stage and multi-stage PA's. Both lumped and distributed matching network synthesis methods are described, with several worked matching network examples. Readers will see a description of a powerful and accessible method that spans multiple RF PA disciplines, including 5G base-station and mobile applications, as well as sat-com and military applications; load-pull with CAD systems is also included. They will review information presented through a practical, hands-on perspective. The book: Helps engineers develop systematic, accurate, and repeatable approach to RF PA design Provides in-depth coverage of using the load-pull method for first-pass design success Offers 150 illustrations and six case studies for greater comprehension of topics
Wireless communication systems require an efficient and broadband RF frontend. RF Power Amplifiers (PA) are the most critical component in the RF frontend and are considered the bottleneck in high efficient wideband transmitters. The research starts with an investigation of high efficient operation modes based on waveform engineering. The outcome of the research can be divided into two main parts: The first concerns an analysis of high efficient modes of operation. The second part builds on first part looking at the PA's efficiency-bandwidth perspective to design a wide band high efficient PA. The first part of the thesis, introduces a novel linear high efficient PA mode termed Injection Power Amplifier (IPA) that exceeds drain efficiency of 90% without relying on the nonlinearity of a PA at the compression region. This is achieved by presenting appropriate negative harmonic impedances to a transistor to reduce the dissipated power, thus, increasing the efficiency of conversion of DC to fundamental RF power. The theoretical analysis of this mode is presented and a validation measurement has been carried out using an active load-pull system. The measured results confirmed the theoretical predictions of achieving high efficiency in a linear PA operation. Furthermore, a PA structure that is based on two parallel PAs (main PA and auxiliary PA) has been proposed along with the practical circuit realization of the IPA mode. In addition, a PA prototype has been designed following a methodology of nonlinear PA design based on waveform engineering. The PA prototype has been characterized and built operating at 0.9 GHz with an output power of 10 W showing a high linear efficient operation of 80% drain efficiency at only 1 dB compression level. The second part of this work aims to tackle today's limitation of high efficient wideband PAs beyond octave bandwidth. A conceptual system based on multimode operation has been proposed to overcome the need for bandlimiting passive harmonic termination. This novel approach is based on combining passive termination with active harmonic injection to get around the theoretical limitation of one octave for high efficiency harmonically tuned power amplifiers. Furthermore, a proof of concept PA prototype has been designed and built for a two octave bandwidth (4:1 bandwidth) operating from 0.63-2.56 GHz and providing the rated output power of a 10 W GaN device with a PAE greater than 50% at only 1 dB compression point. This multi-mode approach shows a promising technique for future wideband high efficiency wireless transmitters.
Book Synopsis A Novel Approach for Wide Band High-efficiency Power Amplifier Design by : Abdullah Almuhaisen
Download or read book A Novel Approach for Wide Band High-efficiency Power Amplifier Design written by Abdullah Almuhaisen and published by . This book was released on 2012 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Wireless communication systems require an efficient and broadband RF frontend. RF Power Amplifiers (PA) are the most critical component in the RF frontend and are considered the bottleneck in high efficient wideband transmitters. The research starts with an investigation of high efficient operation modes based on waveform engineering. The outcome of the research can be divided into two main parts: The first concerns an analysis of high efficient modes of operation. The second part builds on first part looking at the PA's efficiency-bandwidth perspective to design a wide band high efficient PA. The first part of the thesis, introduces a novel linear high efficient PA mode termed Injection Power Amplifier (IPA) that exceeds drain efficiency of 90% without relying on the nonlinearity of a PA at the compression region. This is achieved by presenting appropriate negative harmonic impedances to a transistor to reduce the dissipated power, thus, increasing the efficiency of conversion of DC to fundamental RF power. The theoretical analysis of this mode is presented and a validation measurement has been carried out using an active load-pull system. The measured results confirmed the theoretical predictions of achieving high efficiency in a linear PA operation. Furthermore, a PA structure that is based on two parallel PAs (main PA and auxiliary PA) has been proposed along with the practical circuit realization of the IPA mode. In addition, a PA prototype has been designed following a methodology of nonlinear PA design based on waveform engineering. The PA prototype has been characterized and built operating at 0.9 GHz with an output power of 10 W showing a high linear efficient operation of 80% drain efficiency at only 1 dB compression level. The second part of this work aims to tackle today's limitation of high efficient wideband PAs beyond octave bandwidth. A conceptual system based on multimode operation has been proposed to overcome the need for bandlimiting passive harmonic termination. This novel approach is based on combining passive termination with active harmonic injection to get around the theoretical limitation of one octave for high efficiency harmonically tuned power amplifiers. Furthermore, a proof of concept PA prototype has been designed and built for a two octave bandwidth (4:1 bandwidth) operating from 0.63-2.56 GHz and providing the rated output power of a 10 W GaN device with a PAE greater than 50% at only 1 dB compression point. This multi-mode approach shows a promising technique for future wideband high efficiency wireless transmitters.